Darryl Hudson's
Antique Electric Fan Parts List
This parts list is not the latest and greatest. Go back to the main page at www.HudsonsCustomMachining.com and scroll down to just below the group photo and just above where you see the animated gears turning. There is a link that says Current Parts List with a date at the end of the link. This is the latest and greatest and there is also an order form on the last page with ordering instructions. email me if you have any questions.
The following is a partial list of replacement parts that are available.
If you don't see a part that you need, email me with questions. I can
custom make about anything you need.
STEM |
STEM |
FOOT |
FOOT |
PART # |
.250" (1/4") |
.250" (1/4") |
.500" (1/2") |
.218" (7/32") |
# FR01 |
.281" (9/32") |
.218" (7/32") |
.562" (9/16") |
.157" (5/32") |
# FR02 |
.312" (5/16") |
.250" (1/4") |
.625" (5/8") |
.312" (5/16") |
# FR03 |
.375" (3/8") |
.375" (3/8") |
.750" (3/4") |
.125" (1/8") |
# FR04 |
.406" (13/32") |
.312" (5/16") |
.625" (5/8") |
.093" (3/32") |
# FR05 |
.500" (1/2") |
.281" (9/32") |
.750" (3/4") |
.125" (1/8") |
# FR06 |
BRAND |
STYLE |
YEAR |
TYPE |
COLOR |
PART # |
GE |
Pancake |
1903-07 |
pwr. cord |
black Delrin |
# GEPC10 |
GE |
Pancake |
1903-07 |
pwr. cord |
Ebony wood (as original) |
# GEPC11 |
GE |
Pancake |
1903-07 |
head wire |
black Delrin |
# GEPC12 |
GE |
Pancake |
1903-07 |
head wire |
Ebony wood (as original) |
# GEPC13 |
GROOVE |
GROOVE |
HOLE |
THKNESS |
O.D. |
Note: The following grommets have a groove width of 1/16" and will fit stamped steel type fans. |
||||
.062" (1/16") |
.250" (1/4") |
.125" (1/8") |
.218" (7/32") |
.343" (11/32") |
.062" (1/16") |
.375" (3/8") |
.250" (1/4") |
.187" (3/16") |
.500" (1/2") |
.062" (1/16") |
.437" (7/16") | .187 (3/16") | .187" (3/16') | .750" (3/4") |
.062" (1/16") |
.437" (7/16") |
.250" (1/4") |
.187" (3/16") |
.625" (5/8") |
.062" (1/16") |
.500" (1/2") |
.375" (3/8") |
.281" (9/32") |
.687" (11/16") |
.062" (1/16") |
.562" (9/16") |
.437" (7/16") |
.250" (1/4") |
.750" (3/4") |
Note: The following grommets have a groove width of 1/8" to 3/16" and will fit cast iron type fans. |
||||
.125" (1/8") |
.312" (5/16") |
.187" (3/16") |
.250" (1/4") |
.437" (7/16") |
.125" (1/8") |
.406" (13/32") |
.265" (17/64") |
.375" (3/8") |
.625" (5/8") |
.125" (1/8") |
.437" (7/16") |
.250" (1/4") |
.250" (1/4") |
.625" (5/8") |
.125" (1/8") |
.500" (1/2") |
.312" (5/16") |
.375" (3/8") |
.750" (3/4") |
.125" (1/8") |
.531" (17/32") |
.375" (3/8") |
.500" (1/2") |
.750" (3/4") |
.125" (1/8") |
.562" (9/16") |
.312" (5/16") |
.375" (3/8") |
.812" (13/16") |
.156" (5/32") |
.375" (3/8") |
.281" (9/32") |
.343" (11/32") |
.625" (5/8") |
.187" (3/16") |
.500" (1/2") |
.250" (1/4") |
.437" (7/16") |
.625" (5/8") |
MISCELLANEOUS:
Adams Bagnall, oil cups
Adams Bagnell, C frame, arm to slot guide screw
Breezer, brush caps
Brush caps and brushes, for nearly any make or model......inquire
Carleton 6" oil cups
Carleton, 8" Ball Motor oil cup
Carleton, 8" Ball Motor oil cup holder (screws into motor housing under shaft)
Carleton, 8" ball motor, motor stud (through bolt for motor)
Century, S3 gearbox shaft w/ ball detents, model 152
Century, S4 skeletal centrifugal switch terminal insulators
Century, oiler (complete assy w/ wick tube & spring) for model 351
Cloth Covered wire for power cords and head wire
Colonial, arm to wheel shoulder screw, for tab base model, LH thread
Commandaire, arm to wheel shoulder screw for 10" model
Commandaire, arm to neck shoulder screw for 10" model
Dayton, 8" tab base brush caps (type 22)
Diehl, brush caps, for tab foot/ornate base model
Diehl, oil cup, for tab foot/ornate base model
Diehl, Pullman coach car oiler, for 8" fan, complete or just the cup
Diehl, Pullman coach car oiler screw, fits above shaft, brass
Diehl, Pullman coach car yoke to motor shoulder screw, brass
Diehl, Pullman coach car oiler, for 10" model, complete or just the cup
Diehl, arm to wheel shoulder screw, for Style #F16512 , brass
Eck, Hurricane, grease cup, complete or just the cup or cap
Eck, Hurricane, replacement feet
Eck, Hurricane osc., front bearing for AC model
Eck, Hurricane osc., rear bearing for AC model
Eck, Hurricane osc., front bearing for DC model
Eck, Hurricane stationary front bearing for AC model
Eck, Hurricane stationary rear bearing for AC model
Edison, Oiler drain plug thumbscrew, knurled brass (for 6 blade model)
Edison, pwr. cord terminal hex locknut, brass
Edison, pwr. cord terminal thumbnut, knurled brass
Emerson, 1500/11644 back motor housing screw for rear end of shaft
Emerson, 1500/11644 front rotor keeper, for front end of hollow shaft
Emerson, 1500/11644 pwr. term. binding post thumb nut, blk delrin w/ brass thread insert
Emerson, 1500/11644 rotor keeper shaft & washer
Emerson, 14644 back motor housing screw for rear end of shaft, brass, slotted
Emerson, 14644 brass rotor keeper, fits front end of hollow shaft
Emerson, 14646 front rotor keeper, fits onto front end of hollow shaft
Emerson, 19646 back motor housing screw for rear end of shaft, brass, slotted
Emerson, 21646 osc. connecting arm link
Emerson, 21666 osc. shoulder screw, arm to wheel
Emerson, 26646 rear motor housing bearing plug, brass, LH thread
Emerson, 73646 osc. shoulder screw, arm to wheel
Emerson, acorn nuts, hex brass, set of 4
Emerson, arm to collar shoulder screw
Emerson, blade hub/rotor leather seal, fits 8" & 9"
Emerson, blade hub/rotor leather seal, fits 12" & 16"
Emerson, brass rotor keeper, screws into front end of hollow shaft
Emerson, centrifugal switch insulator
Emerson, fiber washers for rotor/hollow shaft
Emerson, Golden Jubilee shoulder screw, arm to wheel
Emerson, hex bushing, LH thread, screws in rear, guides worm shaft
Emerson, Jr. arm to wheel shoulder screw
Emerson, lever osc. arm to wheel top shoulder screw
Emerson, lever osc. bottom left link shoulderless screw
Emerson, lever osc. lower connecting link to neck
Emerson, lever osc. pinion gear, next to worm gear
Emerson, lever osc. top link shoulder screw
Emerson Northwind 44 brush caps
Emerson, Northwind 450 brush caps
Emerson, Northwind 450 shoulder screw, arm to wheel
Emerson, replacement rubber feet, fits step base fans
Emerson, screw-in grommet, large
Emerson, screw-in grommet, small
Emerson, Silver Swan (pedestal model) oscillator arm link
Emerson, Silver Swan oscillator drive shaft
Emerson, Silver Swan oscillator linkage shoulder screw
Emerson, switch lever knob
Emerson, tripod base pwr. term. binding post screw
Emerson, yoke mount neck set screw, brass w/ square thread, goes into side of ball at top of base
Eskimo, oil cup for 16" cob web guard model w/ 3 prop cast aluminum blade
Fiber washers, various sizes
Fidelity, brush caps for 8" B/B wire yoke model
Fidelity, worm gear and worm, matched set, steel 96 tooth gear
Fidelity, collar, spacer, small, brass
Fidelity, collar, spacer, large, brass
Fidelity, neck stub, brass, connects to arm
Fidelity, oiler, 12" & 16" lever osc., open gear model, 2 pc oiler complete w/ spring & wick
Fidelity, pin, steel, to fit gear to shaft
Fidelity, shoulder screw and hex nut for osc. link, brass
Ft. Wayne, brush caps ,for 8" Woods System ball motor fan
Ft. Wayne, motor nuts, for 8" Woods System ball motor fan
Fueton-Bell Co., Cyclone mixer, brush caps and brush holder
Gears, various, inquire for specifics
GE, 1909 Sidewinder bull gear, large brass, 48 tooth
GE, 1909 Sidewinder front bearing
GE, 1909 Sidewinder rotor shaft, pressed onto your rotor
GE, 1909 Sidewinder shoulder screws, lever linkage (there are 3 different ones, please specify)
GE, 1909 Sidewinder shoulder screw for 48 tooth brass gear
GE, 1909 Sidewinder shoulder screw for 48 tooth brass gear, this one takes a 10-32 nut
GE, 1909 Sidewinder small pinion gear, 9 tooth
GE, 1909 Sidewinder track ball for lever/fork
GE, 1909 Sidewinder transmission engagement knob, brass
GE, 1909 Sidewinder transmission shaft with dbl detent
GE, 1909 Sidewinder worm gear, brass
GE, 1909 Sidewinder worm for back of rotor, steel, drives worm gear
GE, 75423 loop handle osc. arm to wheel shoulder screw, special RH thread
GE, 75423 loop handle osc. arm to wheel shoulder screw, special LH thread
GE, 75423 loop handle motor screw, (special thread), brass
GE, 75423 loop handle rear bearing, (fixed, not self-aligning type) for cast motor & cast base model
GE, A-23 two bulb heater replacement feet
GE, bearings for big motor
GE, bearing set, front/rear, self aligning type
GE, bearing for 16" model made in Wooten, England by GE Ltd. (different than USA model)
GE, big motor oil cup
GE, cage to strut screws, (special thread)
GE, Coin-Op set screw for timing mechanism
GE, DC Ball Motor above bearing screw, brass
GE, kidney osc. arm to wheel shoulder screw, steel
GE, oil cups for big motor, brass
GE, oil cup for loop handle models
GE, oiler for DC ball motor model
GE, screws for cage to strut (special thread)
GE, screws for strut to motor (special thread)
GE, Kidney osc. gearbox engagement pointer
GE, 1897 pancake, acorn nuts
GE, 1897 pancake, oiler, complete with spring & wick
GE, pancake acorn nut, slotted or non-slotted
GE, 12" pancake bearing
GE, 16" pancake bearing (front and rear)
GE, 16" pancake bearing for the England made model by GE Ltd., England
GE, pancake, bushing, for base switch
GE, pancake, grease cup, 1899 model, mounts above shaft
GE, pancake grommets
GE, pancake oiler screw (top side of shaft)
GE, pancake hex nut, brass
GE, pancake oil cup
GE, pancake oil cup holder
GE, pancake oiler complete w/ spring and wick
GE, pancake oiler for 16" model made in England by GE Ltd., complete w/ wick and spring
GE, pancake rotor shaft, 5/16" dia., pressed/pinned to your rotor
GE, pancake terminal insulators, blk, round with square hole
GE, pancake terminal lug, threaded both ends w/ square mid section
GE, pancake terminal thumb nut
GE, pedestal replacement feet
GE, set screw for early blade (special thread)
GE, shoulder screw, arm to wheel, special LH thread
GE, shoulder screw, arm to wheel, special RH thread
GE, star osc. knob (star shape) for gearbox arm to wheel
GE, star osc. knob (star shape) for neck swivel
GE, star osc. knob (star shape) engagement on top of gearbox
GE, star osc. connecting arm bushing
GE star osc. oil cup
GE, strut to motor screw, special thread, brass
GE, Vortalex arm to wheel shoulder screw (special LH thread)
Hamilton Beach brush caps, for models 18, 25, 27, 30, and 33 type mixers/motors
Hamilton Beach, replacement rubber feet
Hamilton Beach, oiler, for fan motor and home motor
Hunter/Century, arm to wheel shoulder screw, Left-Hand thread
Jandus, all brass brush caps
Manhattan #3 battery fan oiler, complete w/ spring and wick, ready to install
Manhattan #3 battery fan, thumbscrew, for pwr terminal
Marelli, brush caps
Marelli, brush holder assy., for 10" S Universal 220V AC/DC
Marelli, oiler for dbl head model, complete w/ spring and wick, brass
Martinot, brush components, for star gear/pin drive oscillator
Menominee, 8" ball motor bearing
Menominee, 8" tab base neck shoulder screw and nut
Menominee, 8" tab base oiler plug
Menominee, 12" ball motor, acorn nut, for strut to motor
Menominee, brush caps, for bank teller fan, knurled brass
Menominee, brush guides, for bank teller fan, brass
Menominee, replacement feet, for bank teller fan
Menominee, feet for tab base, tapered
Menominee, screw-in grommet, large
Menominee, screw-in grommet, small
Menominee, tab base switch knob (ball shaped), brass, for early 8" & 9" vertical switch
MESCO, brush caps, for 110V DC ball motor
Oil cups (custom made).....inquire
Peerless, brush caps for 10" front osc.
Peerless, brush caps, for 110V DC motor, style EE127
Peerless, arm to wheel shoulder screw, for tab base front osc., LH thread w/ nut
Plugs, vintage bakelite (not repros), old style, about 12 different types.....inquire for availability
R&M, 8" List #2835 (32V) brush caps
R&M, arm to wheel shoulder screw for 12" overlapping blade, List #23004
R&M, arm to wheel shoulder screw, for gearback tank motor
R&M, arm to wheel shoulder screw, for 12" osc., List #7804
R&M, brush cap for tank motor
R&M, brush cap for 10" model, List 2203
R&M, brush cap for 10" five blader, List # 2610
R&M, brush cap for 8" List # 2835, 32V DC model
R&M, brush cap for List # 6000 AC/DC model
R&M, flag badge, "The Standard", for 12" & 16" models, brass
R&M, front bearing for List # 2242 30V DC Navy fan
R&M, Lollipop feet
R&M, Lollipop top bearing race
R&M, oil cup for List # 1404
R&M, tank motor grease cup w/ plunger, mounts above shaft, brass
R&M, tank motor, screw in grommet, large
R&M, tank motor, screw in grommet, small
Richmond Portable Battery Fan oiler, complete w/ spring and wick, ready to install
Sami, cannonball motor, brush inspection plug, brass
Sami, cannonball motor, screw, for bottom plate
Sami, cannonball motor, screw, for cage to strut
Springs for Oil Cups, custom wound.......inquire
Tesla, replacement rubber feet
Trojan, oil "slingee", mounts to front snout of motor to catch oil, brass
Trojan, pancake bearing
Tuerk, ceiling fan grommet
Various gears available
Veritys, ball motor osc., rear bearing, for "The Orbit" 16" osc. Made in Birmingham, England
Veritys, ball motor osc., front bearing, for "The Orbit" 16" osc. Made in Birmingham, England
Western Electric, all brass brush caps
Western Electric, all brass oiler, complete or just the cup
Western Electric, Bi Polar oil cup, brass
Western Electric, Bi Polar rear bearing cap, brass
Western Electric, Bi Polar strut screw, ends threaded with hex center
Western Electric, Bi Polar strut screw cap, slotted for screwdriver
Western Electric, brush cap for Tank Motor
Western Electric, screw-in grommet, large
Western Electric, screw-in grommet, small
Westinghouse, brush caps, for all brass
Westinghouse, brush caps, for gyro
Westinghouse, brush holder assembly, for all brass
Westinghouse, oiler, for all brass, complete or just the cup
Westinghouse, arm to neck shoulder screw, for dbl lever
Westinghouse arm to yoke shoulder screw, for dbl lever
Westinghouse, brush cap for Style # 2728540 DC model
Westinghouse, brush holder assembly, for gyro
Westinghouse, cage clip screw for tank motor/dbl lever
Westinghouse, dbl lever, arm shoulder screw
Westinghouse, dbl lever, wheel shoulder screw
Westinghouse, pancake, oiler, brass, complete w/ spring and wick, ready to install
Westinghouse, rear bearing cap for 1917 type osc., brass, threaded, knurled
Westinghouse, stamped steel motor end bell/stator screw, steel
Westinghouse, strut to motor screw for tank motor/dbl lever
Westinghouse, tank motor oil cup, brass
Westinghouse, tank motor, screw in grommet, large
Westinghouse, tank motor, screw in grommet, small
Westinghouse, tank motor/dbl lever yoke to motor shoulder screw, brass
Westinghouse, bushing, for top cage loop
Westinghouse, vane osc. bushing, for vane rod bottom
Westinghouse, vane osc. brush caps
Westinghouse, vane osc. replacement rubber feet
Westinghouse, vane osc., screw-in grommets (large and small)
Westinghouse, vane osc., return stops, brass
Westinghouse, Whirlwind brush caps
Westinghouse, Whirlwind oil cup
White Cross (Lindstrom-Smith) oiler w/ nipple, brass
Wick, material, white, 1/8" dia.
Wick, material, white, 3/16" dia.
Wick, material, white, 1/4" dia.
Wire, cloth covered, several styles......inquire for types and availability
Zeigler Electric Co., brush holder insulators, for candlestick bipolar motor
Zeigler Electric Co., brush clamp terminal lug, for candlestick bipolar motor
Zeigler Electric Co., power terminal lug, brass, for candlestick bipolar motor
Contact Darryl Hudson - darryl@HudsonsCustomMachining.com
|